DTC P0758 2-3 Shift Solenoid Circuit
Electrical 3.8L
The 2-3 shift solenoid
(SS) valve controls the fluid flow acting on the 2-3 shift valves. The 2-3 SS
valve is a normally-open exhaust valve that is used with the 1-2 SS valve in
order to allow four different shifting combinations. The solenoid attaches to
the control valve body within the transmission. The 2-3 SS valve receives
ignition voltage through circuit 239. The powertrain
control module (PCM) controls the solenoid by providing the ground path on
circuit 1223.
When
the PCM detects a continuous open, short to ground or short to power in the 2-3
SS valve circuit, then DTC P0758 sets. DTC P0758 is a
type A DTC.
Conditions
for Running the DTC
- The system voltage is
8-18 volts.
- The engine speed is 450 RPM for
5 seconds.
- The engine is not in fuel cutoff.
Conditions
for Setting the DTC
DTC P0758 sets if
one of the following conditions occurs for 5 seconds.
Condition
1
The PCM commands the
solenoid ON and the voltage feedback remains high (B+).
Condition
2
The PCM commands the
solenoid OFF and the voltage feedback remains low (0 volts).
Action
Taken When the DTC Sets
- The PCM illuminates the malfunction
indicator lamp (MIL).
- The PCM commands third gear only.
- The PCM commands maximum line
pressure.
- The PCM inhibits TCC engagement.
- The PCM freezes shift adapts from
being updated.
- The PCM records the operating
conditions when the Conditions for Setting the DTC are met. The PCM stores
this information as Freeze Frame and Failure Records.
- The PCM stores DTC P0758 in PCM
history.
Conditions
for Clearing the MIL/DTC
- The PCM turns OFF the MIL during the
third consecutive trip in which the diagnostic test runs and passes.
- A scan tool can clear the MIL/DTC.
- The PCM clears the DTC from PCM
history if the vehicle completes 40 warm-up cycles without an
emission-related diagnostic fault occurring.
- The PCM cancels the DTC default
actions when the fault no longer exists and/or the ignition switch is OFF
long enough in order to power down the PCM.
- Inspect the connectors at the PCM,
the 2-3 SS valve and all other circuit connecting points for an
intermittent condition. Refer to Testing
for Intermittent and Poor Connections in Wiring Systems.
- Inspect the circuit wiring for an
intermittent condition. Refer to Testing
for Electrical Intermittents in Wiring
Systems.
- Refer to the Shift
Solenoid Valve State and Gear Ratio table.
The numbers below refer
to the step numbers on the diagnostic table.
|
DTC P0758 2-3 SS Circuit Electrical (3.8L) Step |
Action |
Value(s) |
Yes |
No |
|
Did
you perform the Powertrain Diagnostic System Check?
|
-- |
Go to A
Powertrain On Board Diagnostic (OBD) System Check
in Engine Controls |
||
Important Before
clearing the DTC, use the Scan Tool in
order to record the Freeze Frame and Failure Records. Using the Clear Info
function erases the Freeze Frame and Failure Records from the PCM.
Are
any of the following DTCs also set?
|
-- |
|||
|
Inspect
the ENG C |
-- |
|||
|
Use
the Scan Tool
in order to command the 2-3 SS valve ON and OFF three times while
listening to the bottom of the transmission pan (a stethoscope may be
necessary). Does the solenoid click when commanded? |
-- |
Go to Diagnostic Aids |
||
Does
the test lamp illuminate? |
-- |
|||
Does
the test lamp turn ON and OFF with each command? |
-- |
|||
|
Is
the test lamp always ON? |
-- |
|||
Does
the resistance measure within the specified range? |
19-31 ohms |
|||
|
Measure
the resistance from terminal B to ground, and from terminal E to
ground. Do both readings measure greater than the specified value? |
250 K ohms |
Go to Diagnostic Aids |
||
Does
the resistance measure within the specified range? |
19-31 ohms |
|||
Do
both readings measure greater than the specified value? |
250 K ohms |
|||
|
Important The condition that affects
this circuit may exist in other connecting branches of the circuit. Refer to Power
Distribution Schematics in Wiring Systems for complete circuit
distribution. Test
the power feed circuit (CKT 239) of the 2-3 SS valve for a short to
ground between the engine wiring harness junction block 2 and the AT
inline 20-way connector. Refer to Circuit
Testing and Wiring
Repairs in Wiring Systems. Did you find and correct the condition? |
-- |
|||
|
Important The condition that affects
this circuit may exist in other connecting branches of the circuit. Refer to Power
Distribution Schematics in Wiring Systems for complete circuit
distribution. Test
the power feed circuit (CKT 839) of the 2-3 SS valve for a short to
ground between the AT inline 20-way connector and the 2-3 SS valve.
Refer to Circuit
Testing in Wiring Systems. Did you find a short to ground condition? |
-- |
|||
Did
you complete the replacement? |
-- |
-- |
||
|
Important The condition that affects
this circuit may exist in other connecting branches of the circuit. Refer to Power
Distribution Schematics in Wiring Systems for complete circuit
distribution. Test
the power feed circuit (CKT 239) of the 2-3 SS valve for an open.
Refer to Circuit
Testing and Wiring
Repairs in Wiring Systems. Did you find and correct the condition? |
-- |
-- |
||
|
Test
the control circuit (CKT 1223) of the 2-3 SS valve for a short to
ground between the PCM connector C1 and the AT inline 20-way connector. Refer
to Circuit
Testing and Wiring
Repairs in Wiring Systems. Did you find and correct the condition? |
-- |
|||
|
Test
the control circuit (CKT 1223) of the 2-3 SS valve for an open or
short to power between the PCM connector C1 and the AT inline 20-way
connector. Refer to Circuit
Testing and Wiring
Repairs in Wiring Systems. Did you find and correct the condition? |
-- |
|||
|
Replace
the AT wiring harness assembly. Refer Torque
Converter Clutch Pulse Width Modulation (TCC PWM) Solenoid, TCC Solenoid, and
Wiring Harness . Did you complete the replacement? |
-- |
-- |
||
|
Replace
the 2-3 SS valve. Refer to Control
and Shift Solenoids Replacement . Did you complete the replacement? |
-- |
-- |
||
|
Replace
the PCM. Refer to PCM
Replacement/Programming in Engine Controls. Did you complete the
replacement? |
-- |
-- |
||
|
Perform
the following procedure in order to verify the repair:
Has
the test run and passed? |
-- |
System OK |