DTC P0153 HO2S Slow Response Bank 2 Sensor 1

Circuit Description

The PCM continuously monitors the Heated Oxygen Sensor (HO2S) activity for 100 seconds. During the monitor period the PCM counts the number of times that the HO2S responds from rich to lean and from lean to rich and adds the amount of time it took to complete all transitions. With this information, the PCM can determine the average time for all transitions. If the average response time is too slow, a DTC sets.

The PCM determines the lean to rich transition when the HO2S voltage changes from less than 300 mV to greater than 600 mV. The PCM determines the rich to lean transition when the HO2S voltage changes from more than 600 mV to less than 300 mV. An HO2S that responds too slowly is most likely defective. Replace the HO2S.

Conditions for Running the DTC

• DTCs P0101, P0102, P0103, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0335, P0336, P0351-P0358, P1258 not set.
• The engine coolant temperature is greater than 65°C (149°F).
• The ignition voltage is greater than 9.0 volts.
• The AIR, EGR, and the Catalyst diagnostics are not active.
• The fuel system is operating in Closed Loop.
• The engine speed is between 1,000 RPM and 2,300 RPM.
• The engine air flow between 15 g/s and 35 g/s.
• The EVAP canister purge duty cycle is greater than 0%.
• The engine run time is greater than 120 seconds.

Conditions for Setting the DTC

• The lean to rich response (below 300 mV to above 600 mV) average time is greater than 100 milliseconds.
• The rich to lean response (above 600 mV to below 300 mV) average time is greater than 100 milliseconds.
• The above conditions are met for 100 seconds.

Action Taken When the DTC Sets

• The PCM illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
• The PCM records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the PCM stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the PCM records the operating conditions at the time of the failure. The PCM writes the conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

• The PCM turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
• A last test failed, or current DTC, clears when the diagnostic runs and does not fail.
• A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
• Use a scan tool in order to clear the MIL and the DTC.

Diagnostic Aids

Important

• Remove any debris from the PCM connector surfaces before servicing the PCM. Inspect the PCM connector gaskets when diagnosing/replacing the PCM. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion into the PCM.
• For any test that requires probing the PCM or component harness connectors, use the Connector Test Adapter Kit J 35616-A . Using this kit prevents any damage to the harness connector terminals.

• A malfunction in the HO2S heater circuits will cause a DTC to set. Test the HO2S heater circuits for intermittent opens/connections. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.
• An oxygen supply inside the HO2S is necessary for proper operation. The HO2S wires provides the supply of oxygen. Inspect the HO2S wires and connections for breaks or contamination. Refer to Heated Oxygen Sensor (HO2S) Wiring Repairs in Wiring Systems.
• Using the Freeze Frame and/or Failure Records data may aid in locating an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data can help determine how many miles since the DTC set. The Fail Counter and Pass Counter can also help determine how many ignition cycles the diagnostic reported a pass and/or a fail. Operate the vehicle within the same freeze frame conditions (RPM, load, vehicle speed, temperature etc.) that you observed. This will isolate when the DTC failed.
• For an intermittent condition, refer to Symptoms .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

2. This step determines if the fault is present. This test may take 5 minutes for the diagnostic to run. For any test that requires probing the PCM or a component harness connector, use the Connector Test Adapter Kit J 35616-A . Using this kit prevents damage to the harness connector terminals.

3. When DTCs P0133 and P0153 are set at the same time, this is a good indication that a fuel contamination condition is present.

4. An exhaust leak 6-12 inches away from the HO2S can cause a DTC to set.

5. This step verifies whether a good ground circuit is available.

6. This step tests the integrity of the signal circuit to the PCM.

7. This step tests the integrity of the signal circuit to the PCM.

8. Certain RTV silicone gasket materials give off vapors that can contaminate the HO2S. There is also a possibility of silicone contamination caused by silicone in the fuel. If the sensors appear to be contaminated by silicone and all the silicone sealant is a non silicone base, advise the customer to try a different fuel company. A missing fuel filler restrictor indicates the customer may have used leaded fuel.

Step	Action	Value(s)	Yes	No
1	Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?	--	Go to Step 2	Go to A Powertrain On Board Diagnostic (OBD) System Check
2	Important If any DTCs are set (except P0133), refer to those DTCs before proceeding with this diagnostic table. Install a scan tool. Idle the engine at the normal operating temperature. Operate the vehicle within parameters specified under Conditions for Running the DTC in the supporting text. Monitor the Diagnostic trouble Code (DTC) Information using the scan tool. Does the scan tool indicate that DTC P0153 test failed this ignition?	--	Go to Step 3	Go to Diagnostic Aids
3	Did the scan tool also indicate that P0133 failed this ignition?	--	Go to Step 8	Go to Step 4
4	Inspect the exhaust system for leaks. Refer to Exhaust Leakage in Engine Exhaust. After you inspect the exhaust system return to this diagnostic. If you find an exhaust leak repair the exhaust as necessary. Did you find and correct the condition?	--	Go to Step 2	Go to Step 5
5	Visually/physically inspect the following items: Ensure that the HO2S is securely installed. Inspect for corrosion on the terminals. Test the terminal tension at the HO2S and at the PCM. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems. Inspect for damaged wiring. Did you find a concern in any of the above areas?	--	Go to Step 9	Go to Step 6
6	Disconnect the Bank 2 HO2S 1. Jumper the HO2S low (PCM side) signal circuit to a ground. Monitor the Bank 2 HO2S 1 voltage on the Engine 1 Data List using a scan tool. Does the scan tool indicate a voltage within the specified range?	350-550 mV	Go to Step 7	Go to Step 10
7	Jumper the Bank 2 HO2S 1 high and low (PCM side) signal circuits to a ground. Monitor the Bank 2 HO2S 1 voltage using a scan tool. Does the scan tool indicate a voltage below the specified value?	200 mV	Go to Step 12	Go to Step 11
8	Important Determine and correct the cause of the contamination before replacing a sensor. Inspect for the following conditions: Fuel contamination. Refer to Alcohol/Contaminants-in-Fuel Diagnosis . Use of improper RTV sealant Engine oil/coolant consumption Replace the affected HO2S. Refer to Heated Oxygen Sensor (HO2S) Replacement - Bank 1 and/or Heated Oxygen Sensor (HO2S) Replacement - Bank 2 . Is the action complete?	--	Go to Step 13	--
9	Repair condition as necessary. Is the action complete?	--	Go to Step 13	--
10	Repair the open Bank 2 HO2S 1 low signal circuit or, the grounded Bank 2 HO2S 1 high signal circuit. Refer to Wiring Repairs in Wiring Systems. Is the action complete?	--	Go to Step 13	--
11	Repair the open Bank 2 HO2S 1 high signal circuit or, the faulty PCM connections. Refer to Wiring Repairs in Wiring Systems. Is the action complete?	--	Go to Step 13	--
12	Replace the Bank 2 HO2S 1. Refer to Heated Oxygen Sensor (HO2S) Replacement - Bank 2 . Is the action complete?	--	Go to Step 13	--
13	Select the Diagnostic Trouble Code (DTC) option and the Clear DTC Information option using the scan tool. Idle the engine at the normal operating temperature. Select the Diagnostic Trouble Code (DTC) option and the Specific DTC option, then enter the DTC number using the scan tool. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text, if applicable. Does the scan tool indicate that this test ran and passed?	--	Go to Step 14	Go to Step 2
14	Select the Capture Info option and the Review Info option using the scan tool. Does the scan tool display any DTCs that you have not diagnosed?	--	Go to the applicable DTC table	System OK